Influence of Die Material of Press on Operation

To be able to solve this issue, you have to trobleshoot and fix the issue, so how to approach grinding punch punch machine can't go back to punch failure, through the slider tightly around the handle, press the bond, with the punching machine On the table fixed using the guide pin from the template, the lower and upper die, guide sleeve. Work, stripping stop pin, waterfall and slider mode, first press the position of the discharge plate material, after which press the punch mold material. Within the die-cutting round billet positioning, downward movement, blank pressure, in the hole, and then fall under the cavity, leading to permanent deformation rubber stamping die material, after processing the work surface needed. Once the work surface between your punch and also the top sheet takes place, the waste is firmly fixed towards the punch.
Within the camera mode, the punch presses the spring work piece by spring pressure in the die wasting the coil with the discharge plate simultaneously because the elastic spring, in order to complete the entire process. The fabric is distributed towards the step, for the following process, and so forth. The release from the punch press is the fact that many reasons exist why the various remedies are different: 1, accurate positioning Inaccurate positioning or feed device could be adjusted or given towards the device. 2, guide pin, resulting in the movement is away from the solution easily, can switch the guide column. 3, puncture injuries or appearance isn't smooth, but additionally can build the punch mold emissions, could be solved, not rubber stamping. 4, lifting equipment set not reasonable, reset. 5, the lack of ejector or elimination of material shortage, by altering the spring or spring processing separator punch quotes xenophobia. Within the punch press, the slide block is driven through the mold so the action, the primary and auxiliary rubber stamping effects, the slider should follow certain concepts to satisfy the processing needs, then your design, the slider should stick to the principle design. 1. Set up in the punch Press the slider from the body ought to be simple, compact structure, reasonable layout, easy installation, so far as possible through the sliding body from the geometric core sliding parts center punch recipes for a crowd. 2. To guarantee the precision from the slider, it ought to possess the appropriate precision needs, guide length is enough. 3. Reasonable mix-sectional dimensions and strength from the plate position, underneath the premise of strength and stiffness, minimize the load from the slider, travel. Since the slider structure is comparatively complex, within the design process to concentrate on it, more taken into consideration. ??In to solve this issue, need to handle failure, then how should cope with the failure from the punch punch punch cannot be punched, the punch with the mold block rubber stamping, punching machine connection, Rubber stamping machine table used within the next fixed template hole punch shapes, the lower and upper die using the guide column, guide sleeve guide. When working, the steel strip on the positioning of the stop pin, once the mold using the slider around the waterfall, press the fabric from the stripper plate, after which punch the punch mold material to acquire. The punch blank lies within the lower die, moving downward in blank pressure, in the hole, and is constantly on the descend in to the cavity, leading to permanent deformation from the material within the rubber stamping die following the preferred work surface is machined. Once the work surface is clamped between your punch and also the top block, the waste can also be firmly fixed towards the press. Punch manufacturers within the camera mode, the very best bit of the work surface with the elastic spring pressure ejector in the mold the same time frame down the sink within the hoop, through the discharge plate through the spring pressure, thus finishing the whole process. Material to some step, the procedure for the following step, so backwards and forwards.
Many reasons exist for that press die unloading, the reason why for various treatment options won't be the same: 1, the actual positioning of feeding devices are not accurate or feeding adjustable feeding or positioning device. 2, the interior guide column pull, leading to movement isn't smooth, could be replaced inside the column-oriented solutions. 3, perforation damage or appearance isn't smooth, but the formation of rubber stamping die discharge, can switch the rubber stamping solution. 4, the very best material device set not reasonable, reset. 5, the inadequacy from the ejector or remove the possible lack of material, by replacing the spring or spring handle stripper. Punch, the function from the slider would be to drive the mold to accomplish the experience, mainly to experience another hot rubber stamping effect, slider design should follow certain concepts to satisfy the processing needs then, the slider should stick to the design concepts. 1. Placed on the punch slider around the various institutions ought to be simple structure, compact, rational layout, easy installation and adjustment, so far as possible so the center of sliding components with the geometric core slider body. 2. To guarantee the precision from the punch around the slider, it ought to possess the appropriate precision needs, and guide the size of sufficient. 3. Underneath the premise of strength and rigidity, reasonably determine the mix-sectional size and the position of the reinforcement plate to reduce the load from the slider, travel. 4. Since the slider structure is much more complex, within the design ought to be more attention into it while comprehensive consideration.